Finally low-pressure success: drip hose that works

January 3, 2009

Low pressure drip systemA low-pressure drip water system attached to the wheelie bin gives a passive watering system. I am really pleased this irrigation product (low pressure drip hose)  is available. I also avoided buying the wrong type of piping: I went into the store intending to buy the brown version.

T-joint connecting poly pipe from wheelie bin to drip hose

The helpful woman at Croydon Bunnings suggested I need a T-joint where the drip pip joins the pipe from the wheeliebin. I followed this advice and my guess is that it equalises the pressure of the flow in the pipes. (The green pipe in the photo starts at the T-joint on the right side)

Close up T-joint

By using some basic hose fittings, including a small valve and some low pressure drip feed hose bought at Bunnings (AUS $55 ), I was able to create a watering system that really works: every dripper was dripping, and you can turn it on or off easily. The wheeliebin was nearly empty after several hours. If you take a close look you can see a drip coming out of the pipe. Low pressure drip hose, success

Finally I have figured out the best way to set this system up!

Drippers are inside the pipe every 30 cm (12″)

Dripper every 30 cm (12")

And the photo at the bottom is the area I am trying to keep alive during this drought, a drought that seems to have no end and seems to be signalling this is the climate of the future. The garden

Photos taken with a Pentax K-m: an excellent intro level DSLR.


Better use of the water

December 30, 2008

If you fit an outlet at the bottom and connect this this to a length of poly pipe, and fit this pipe to a slow dripping or trickle feed type hose, the bin will always be slowly watering the garden.

I used the black recycled car-tyre hose, but this has stopped working, perhaps from under-use. So I am off to Bunnings in the next week to buy some of the pale brown poly drip hose that looks less likely to clog. Photos when I am done.

Keeping out the mozzies (mosquitoes)

April 20, 2008

I noticed were were breeding mosquitoes. So I tiied pouring vegetable oil into the wheeliebin. All good: after a day or so they were all dead. But after several weeks the oil turned into a revolting slimy, sticky, putrid mess. Not a solution. don’t use it.

Step 6: Add the downpipe diverter

November 15, 2007

downpipe diverterThe next major task is to fit the downpipe diverter to the dowpipe. I used a simple hacksaw to cut a section from the downpipe. Make sure you do not cut too much off! It’s easy to do! Remember that some of the downpipe has to sit inside of the diverter, which means that what you cut has to be less than the length of the diverter. (In the photo here you can see the end of the diverter: actually its the pice of downpipe I added to the end of the diverter to give the setup extra reach.)

Step 5: Fit the mesh

November 15, 2007

MeshSo the water runs in and keep the debris out, cut a hole in the top, and fit the flywire. A jigsaw is a fast way to cut the hole (photo). Then drill holes for the rivets and rivet the mesh on. The mesh also keeps out the mosquitoes.

Cut off the excess to reduce the trippping hazard, add the hose fitting

November 15, 2007

remove the excessStep 1: Remove what you want with a hacksaw. If your wheeliebin will be in that narrow space between the fence and the house, cutting excess will reduce the trippping hazard, especially if you have to squeeze your way past the bin is on the way to the gas hot water service in the dark to relight the pilot light.

Step 2: Screw on the hose fitting, ready for the next step. If a hose is not connected, what will keep the water in? You might add a hose with a snap-close fitting on the other end as a simpler way to do this.

hose fitting attached

Step 3: Clean out the drill hole

October 23, 2007

Clean out the drill hole

This odd looking device that resembles a trunk of a tree is in fact a rasp, one uses to smooth the edges of the drill hole. It is a rough file. Step 4 (we can only dream) might be more exciting.

And here’s what were getting ready to fit.Exit fitting